Recent flights

I've flown a couple of times since my last post - both solo and both just local flights.

The first was to check out the infestation of duckweed on the pond we have down in Fairfield county. We had plans to get down there for the weekend and I wanted to learn how much duckweed we'd have to treat. I found it about 60% covered which wasn't great. After talking to my Dad about it, we decided to buy some Talapia fish to stock the pond. The hope is that after putting 1000+ small Talapia in the pond they will start to eat the duckweed and make a dent in it. We've been spraying chemicals for years with only minimal benefit. Hopefully the au-naturale method will work. Either that, or the bass will get lots of fish food.

This morning I went out early to visit an old haunt - KFQD in N.C. It is just south of the mountain foothills so there's some very nice scenery to take in. The flight went great, especially my landing at FQD. Unfortunately my landing was less than perfect back at KUZA as I had a little bounce. And, of course, people were watching me do it - people NEVER airplane watch there, but they caught that landing! :)

My desire to own an airplane is starting to ramp up again. i am renting a wonderful plane now, but it is still renting. That means scheduling is a bit annoying - no last minute decisions to fly after seeing that you have 2 hours to spare when the wx is wonderful.

How does one quantify their desire to own an airplane? I judge it by the number of times I window shop on controller.com. And that number has been rising. :)

Comments

ddf said…
The used airplane prices are looking so good right now, it is really hard to resist. However it impossible to justify a new, major expense with on going charges to the CFO. She is looking to cut back, not inflate our household budget...not very stimulating.
June 9, 2009 at 1:22 PM
Post a Comment

Popular posts from this blog

Updating data on the Garmin Perspective system

Image
After changing from the Avidyne system to the Cirrus Perspective (G1000) system, I had to relearn an important part of owning an airplane: how to update all the data the systems use. There's even more data in the Perspective, including AOPA directory data and more charts. In this walkthrough, I make use of the Jeppesen app for Apple OS X: JDM .  It has worked well for me, though I did need to call Jeppesen when I first set this up to get my subscriptions fixed up.  They gave great customer support when I did. The process starts (optionally) by hooking up a ground power unit (GPU).  In the case of the Cirrus, you can certainly do this without it, but I tend to hook it up just to be sure.  The systems draw about 8-10amps while updating, but you won't generally have the power on for long.  One tip I've read: power up the GPU before plugging it into the plane, at least for the one I bought.  That saves the plane from seeing any power spikes that might have occurred when t
Read more

G1000 transistion training - emergencies - final flight

Image
For the final flight in my G1000 transition course we focused on failure scenarios. Not the "engine goes POOF" kind but the avionics kind. Normal situation This picture shows what the 2 Garmin screens show in a normal (non failure) situation. You can see we have 2 screens - the left PFD focusing on flight performance (airspeed, heading, attitude, altitude) and the right screen (MFD) focusing on engine data, mapping, checklists, and everything else. Failed PFD screen In this scenario the screen that is right in front of you (the PFD) has failed. This basically means the screen has gone dark. We simulate that by dimming the screen down to 0% brightness. After darkening the PFD we shot a GPS approach into Rock Hill. When this failure has occured you shift the G1000 into Reversionary mode. That means the info that is normally split across 2 screens is now merged into 1. It actually duplicates the same data on both screens, but since the PFD screen is no longer functioning
Read more

A-10C Standby Compass - Sun Shade

Image
 One of the final items to add to this instrument build (besides the text covers for the lower LEDs) was the sun shade for the AR LED box.  I made this out of thin aluminum sheets , cutting it from a template using some metal sheers .    My template was created by tracing some of the actual artwork from the DCS sim, and then scaling it to the proper size. It turned out ok, not perfect but pretty good.  Primed and painted it and then installed it using 2 of the 4 holes that were already on the LED box 3D print.  I used some heat inserts in those holes to give the screws something to bite, but the holes are really too big for my inserts so had to use some glue to help out.  
Read more